Misplaced Pages

This is an old revision of this page, as edited by 125.190.137.42 (talk) at 06:50, 28 February 2006 (→External links). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

The field-effect transistor (FET) is a transistor that relies on an electric field to control the shape and hence the conductivity of a 'channel' in a semiconductor material. FETs are sometimes used as voltage-controlled resistors. The concepts related to the field effect transistor predated those of the bipolar junction transistor (BJT). Nevertheless, FETs were implemented only after BJTs due to the simplicity of manufacturing BJTs over FETs at the time.

A FET has three terminals, which are known as the gate, drain and source. (Compare these to the terms used for BJTs: base, collector and emitter.) The voltage applied between the gate and source terminals modulates the current between the source and drain terminals. There may also be a fourth terminal on some MOSFETs called the body (or bulk), which sets the threshold voltage for operation. There are two 'modes' of FET: enhancement, in which a voltage applied to the gate increases the current flow from source to drain; and depletion, in which a voltage applied decreases the current flow from source to drain. Thus enhancement FETs are normally off, whereas depletion FETs are normally on.

Most FETs are made with conventional bulk semiconductor processing techniques, using the single crystal semiconductor wafer as the active region, or channel.

Types of field-effect transistors

The FET is simpler in concept than the bipolar transistor and can be constructed from a wide range of materials. The channel region of any FET is either doped to produce n-type semiconductor, giving an "N-channel" device, or with p-type to give a "P-channel" device. The doping determines the polarity of gate operation. The different types of field-effect transistors can be distinguished by the method of isolation between channel and gate:

• The MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor) utilizes an insulator (typically SiO₂).
• The JFET (Junction Field-Effect Transistor) uses a p-n junction as the gate.
• The MESFET (Metal-Semiconductor Field-Effect Transistor) substitutes the p-n-junction of the JFET with a Schottky barrier; used in GaAs and other III-V semiconductor materials.
• Using bandgap engineering in a ternary semiconductor like AlGaAs gives a HEMT (High Electron Mobility Transistor), also called an HFET (heterostructure FET). The fully depleted wide-band-gap material forms the isolation.

Among the more unusual body materials are amorphous silicon, polycrystalline silicon or other amorphous semiconductors in thin-film transistors or organic field effect transistors that are based on organic semiconductors and often apply organic gate insulators and electrodes.

FET Operation

The shape of the conducting channel in a FET is altered when a potential difference is applied to the gate terminal (potential relative to either source or drain.) In an n-channel "depletion-mode" device, a negative gate voltage causes a depletion region to expand in size and encroach on the channel from the side, narrowing the channel. If the depletion region completely closes the channel, the resistance of the channel becomes very large, and the FET is effectively turned off. Positive gate voltage attracts electrons from the surrounding semiconductor next to the gate, forming a conductive channel. At low source-to-drain voltages, small changes to the gate voltage will alter the channel resistance. In this mode the FET operates like a variable resistor. This mode is not employed when amplification is needed.

If a larger potential difference is applied between the source and drain terminals, this creates a significant current in the channel and produces a gradient of potential from source to drain. This also causes the shape of the depletion region to become asymmetrical–one end of the channel becomes narrow. If the potential difference is large enough, the depletion region begins to close the channel. The FET is said to be in saturation. Rather than entirely blocking the electrons from flowing from source to drain, electrons flow through the depletion region in a controlled manner. Any attempted increase of the drain-to-source voltage will lengthen the depletion region, increasing the channel resistance proportionally with the applied drain-to-source voltage which causes the value of drain current to remain relatively fixed. This mode of operation is called pinch-off. In this mode, the FET behaves as a constant-current source rather than as a resistor and can be used as a voltage amplifier. The value of gate voltage determines the value of the constant current in the channel.

An "enhancement-mode" device is of slightly more complex construction. Rather than one being one material, is made of a three-piece sandwich: similar to either an npn or a pnp transistor with no base connection, but still with a gate. In this case, the device is "normally-off" since one of the two junctions will always be reverse biased. The npn device is called a n-channel device and the pnp device is called an p-channel device.

Uses

The most commonly used FET is the MOSFET. The CMOS (complementary metal oxide semiconductor) process technology is the basis for modern digital integrated circuits. This process technology uses an arrangement where the (usually "enhancement-mode") p-channel MOSFET and n-channel MOSFET are connected in series such that when one is on, the other is off. In CMOS logic devices, the p-channel device pulls up the output and the n-channel device pulls down the output. The great advantage of CMOS circuits is that they allow no current to flow (ideally), except during the transition from one state to the other, which is very short. The gates are capacitive, and the charging and discharging of the gates each time a transistor switches states is the primary source of power usage in fast CMOS logic circuits.

The fragile insulating layer of the MOSFET between the gate and channel makes it vulnerable to electrostatic damage during handling. This is not usually a problem after the device has been installed.

FETs can switch signals of either polarity on the source or drain terminals, if their amplitude is significantly less than the gate swing, as the devices are typically symmetrical. This makes FETs suitable for switching analog signals between paths (multiplexing). With this concept, one can construct a solid-state mixing board, for example.

The power MOSFET has a reverse-biased 'parasitic diode' shunting the conduction channel that has half the current capacity of the conduction channel. Sometimes this diode is used when driving inductive circuits, but in other cases it causes problems.

A more recent device for power control is the insulated-gate bipolar transistor, or IGBT. This has a control structure akin to a MOSFET coupled with a bipolar-like main conduction channel. These have become quite popular.

External links

• PBS The Field Effect Transistor
• Junction Field Effect Transistor
• Field Effect Transistors
• The Enhancement Mode MOSFET
• CMOS gate circuitry
• Winning the Battle Against Latchup in CMOS Analog Switches
• Free IC DataSheet Search Site : http://www.Datasheet4U.com

• Transistors