Misplaced Pages

This article has multiple issues. Please help improve it or discuss these issues on the talk page. (Learn how and when to remove these messages) This article may require cleanup to meet Misplaced Pages's quality standards. The specific problem is: the article goes on for way too long about various technical aspects that aren't necessary for the article. Please help improve this article if you can. (December 2022) (Learn how and when to remove this message) This article may be too technical for most readers to understand. Please help improve it to make it understandable to non-experts, without removing the technical details. (December 2022) (Learn how and when to remove this message) (Learn how and when to remove this message)

A mechanical calculator, or calculating machine, is a mechanical device used to perform the basic operations of arithmetic automatically, or (historically) a simulation such as an analog computer or a slide rule. Most mechanical calculators were comparable in size to small desktop computers and have been rendered obsolete by the advent of the electronic calculator and the digital computer.

Surviving notes from Wilhelm Schickard in 1623 reveal that he designed and had built the earliest of the modern attempts at mechanizing calculation. His machine was composed of two sets of technologies: first an abacus made of Napier's bones, to simplify multiplications and divisions first described six years earlier in 1617, and for the mechanical part, it had a dialed pedometer to perform additions and subtractions. A study of the surviving notes shows a machine that would have jammed after a few entries on the same dial, and that it could be damaged if a carry had to be propagated over a few digits (like adding 1 to 999). Schickard abandoned his project in 1624 and never mentioned it again until his death 11 years later in 1635.

Two decades after Schickard's supposedly failed attempt, in 1642, Blaise Pascal decisively solved these particular problems with his invention of the mechanical calculator. Co-opted into his father's labour as tax collector in Rouen, Pascal designed the calculator to help in the large amount of tedious arithmetic required; it was called Pascal's Calculator or Pascaline.

In 1672, Gottfried Leibniz started designing an entirely new machine called the Stepped Reckoner. It used a stepped drum, built by and named after him, the Leibniz wheel, was the first two-motion calculator, the first to use cursors (creating a memory of the first operand) and the first to have a movable carriage. Leibniz built two Stepped Reckoners, one in 1694 and one in 1706. The Leibniz wheel was used in many calculating machines for 200 years, and into the 1970s with the Curta hand calculator, until the advent of the electronic calculator in the mid-1970s. Leibniz was also the first to promote the idea of an Pinwheel calculator.

Thomas' arithmometer, the first commercially successful machine, was manufactured two hundred years later in 1851; it was the first mechanical calculator strong enough and reliable enough to be used daily in an office environment. For forty years the arithmometer was the only type of mechanical calculator available for sale until the industrial production of the more successful Odhner Arithmometer in 1890.

The comptometer, introduced in 1887, was the first machine to use a keyboard that consisted of columns of nine keys (from 1 to 9) for each digit. The Dalton adding machine, manufactured in 1902, was the first to have a 10 key keyboard. Electric motors were used on some mechanical calculators from 1901. In 1961, a comptometer type machine, the Anita Mk VII from Sumlock comptometer Ltd., became the first desktop mechanical calculator to receive an all-electronic calculator engine, creating the link in between these two industries and marking the beginning of its decline. The production of mechanical calculators came to a stop in the middle of the 1970s closing an industry that had lasted for 120 years.

Charles Babbage designed two new kinds of mechanical calculators, which were so big that they required the power of a steam engine to operate, and that were too sophisticated to be built in his lifetime. The first one was an automatic mechanical calculator, his difference engine, which could automatically compute and print mathematical tables. In 1855, Georg Scheutz became the first of a handful of designers to succeed at building a smaller and simpler model of his difference engine. The second one was a programmable mechanical calculator, his analytical engine, which Babbage started to design in 1834; "in less than two years he had sketched out many of the salient features of the modern computer. A crucial step was the adoption of a punched card system derived from the Jacquard loom" making it infinitely programmable. In 1937, Howard Aiken convinced IBM to design and build the ASCC/Mark I, the first machine of its kind, based on the architecture of the analytical engine; when the machine was finished some hailed it as "Babbage's dream come true".

Ancient history

The desire to economize time and mental effort in arithmetical computations, and to eliminate human liability to error, is probably as old as the science of arithmetic itself. This desire has led to the design and construction of a variety of aids to calculation, beginning with groups of small objects, such as pebbles, first used loosely, later as counters on ruled boards, and later still as beads mounted on wires fixed in a frame, as in the abacus. This instrument was probably invented by the Semitic races and later adopted in India, whence it spread westward throughout Europe and eastward to China and Japan.
After the development of the abacus, no further advances were made until John Napier devised his numbering rods, or Napier's Bones, in 1617. Various forms of the Bones appeared, some approaching the beginning of mechanical computation, but it was not until 1642 that Blaise Pascal gave us the first mechanical calculating machine in the sense that the term is used today.

— Howard Aiken, Proposed automatic calculating machine, presented to IBM in 1937

A short list of other precursors to the mechanical calculator must include a group of mechanical analog computers which, once set, are only modified by the continuous and repeated action of their actuators (crank handle, weight, wheel, water...). Before the common era, there are odometers and the Antikythera mechanism, a seemingly out of place, unique, geared astronomical clock, followed more than a millennium later by early mechanical clocks, geared astrolabes and followed in the 15th century by pedometers. These machines were all made of toothed gears linked by some sort of carry mechanisms. These machines always produce identical results for identical initial settings unlike a mechanical calculator where all the wheels are independent but are also linked together by the rules of arithmetic.

The 17th century

Overview

The 17th century marked the beginning of the history of mechanical calculators, as it saw the invention of its first machines, including Pascal's calculator, in 1642. Blaise Pascal had invented a machine which he presented as being able to perform computations that were previously thought to be only humanly possible.

In a sense, Pascal's invention was premature, in that the mechanical arts in his time were not sufficiently advanced to enable his machine to be made at an economic price, with the accuracy and strength needed for reasonably long use. This difficulty was not overcome until well on into the nineteenth century, by which time also a renewed stimulus to invention was given by the need for many kinds of calculation more intricate than those considered by Pascal.

— S. Chapman, Pascal tercentenary celebration, London, (1942)

The 17th century also saw the invention of some very powerful tools to aid arithmetic calculations like Napier's bones, logarithmic tables and the slide rule which, for their ease of use by scientists in multiplying and dividing, ruled over and impeded the use and development of mechanical calculators until the production release of the arithmometer in the mid 19th century.

Invention of the mechanical calculator

In 1623 and 1624 Wilhelm Schickard, in two letters that he sent to Johannes Kepler, reported his design and construction of what he referred to as an “arithmeticum organum” (“arithmetical instrument”), which would later be described as a Rechenuhr (calculating clock). The machine was designed to assist in all the four basic functions of arithmetic (addition, subtraction, multiplication and division). Amongst its uses, Schickard suggested it would help in the laborious task of calculating astronomical tables. The machine could add and subtract six-digit numbers, and indicated an overflow of this capacity by ringing a bell. The adding machine in the base was primarily provided to assist in the difficult task of adding or multiplying two multi-digit numbers. To this end an ingenious arrangement of rotatable Napier's bones were mounted on it. It even had an additional "memory register" to record intermediate calculations. Whilst Schickard noted that the adding machine was working, his letters mention that he had asked a professional, a clockmaker named Johann Pfister, to build a finished machine. Regrettably it was destroyed in a fire either whilst still incomplete, or in any case before delivery. Schickard abandoned his project soon after. He and his entire family were wiped out in 1635 by bubonic plague during the Thirty Years' War.

Schickard's machine used clock wheels which were made stronger and were therefore heavier, to prevent them from being damaged by the force of an operator input. Each digit used a display wheel, an input wheel and an intermediate wheel. During a carry transfer all these wheels meshed with the wheels of the digit receiving the carry.

Blaise Pascal invented a mechanical calculator with a sophisticated carry mechanism in 1642. After three years of effort and 50 prototypes he introduced his calculator to the public. He built twenty of these machines in the following ten years. This machine could add and subtract two numbers directly and multiply and divide by repetition. Since, unlike Schickard's machine, the Pascaline dials could only rotate in one direction zeroing it after each calculation required the operator to dial in all 9s and then (method of re-zeroing) propagate a carry right through the machine. This suggests that the carry mechanism would have proved itself in practice many times over. This is a testament to the quality of the Pascaline because none of the 17th and 18th century criticisms of the machine mentioned a problem with the carry mechanism and yet it was fully tested on all the machines, by their resets, all the time.

Pascal's invention of the calculating machine, just three hundred years ago, was made while he was a youth of nineteen. He was spurred to it by seeing the burden of arithmetical labour involved in his father's official work as supervisor of taxes at Rouen. He conceived the idea of doing the work mechanically, and developed a design appropriate for this purpose; showing herein the same combination of pure science and mechanical genius that characterized his whole life. But it was one thing to conceive and design the machine, and another to get it made and put into use. Here were needed those practical gifts that he displayed later in his inventions...

— S. Chapman, Pascal tercentenary celebration, London, (1942)

In 1672, Gottfried Leibniz started working on adding direct multiplication to what he understood was the working of Pascal's calculator. However, it is doubtful that he had ever fully seen the mechanism and the method could not have worked because of the lack of reversible rotation in the mechanism. Accordingly, he eventually designed an entirely new machine called the Stepped Reckoner; it used his Leibniz wheels, was the first two-motion calculator, the first to use cursors (creating a memory of the first operand) and the first to have a movable carriage. Leibniz built two Stepped Reckoners, one in 1694 and one in 1706. Only the machine built in 1694 is known to exist; it was rediscovered at the end of the 19th century having been forgotten in an attic in the University of Göttingen.

In 1893, the German calculating machine inventor Arthur Burkhardt was asked to put Leibniz's machine in operating condition if possible. His report was favorable except for the sequence in the carry.

Leibniz had invented his namesake wheel and the principle of a two-motion calculator, but after forty years of development he wasn't able to produce a machine that was fully operational; this makes Pascal's calculator the only working mechanical calculator in the 17th century. Leibniz was also the first person to describe a pinwheel calculator. He once said "It is unworthy of excellent men to lose hours like slaves in the labour of calculation which could safely be relegated to anyone else if machines were used."

Other calculating machines

Schickard, Pascal and Leibniz were inevitably inspired by the role of clockwork which was highly celebrated in the seventeenth century. However, simple-minded application of interlinked gears was insufficient for any of their purposes. Schickard introduced the use of a single toothed "mutilated gear" to enable the carry to take place. Pascal improved on that with his famous weighted sautoir. Leibniz went even further in relation to the ability to use a moveable carriage to perform multiplication more efficiently, albeit at the expense of a fully working carry mechanism.

...I devised a third which works by springs and which has a very simple design. This is the one, as I have already stated, that I used many times, hidden in the plain sight of an infinity of persons and which is still in operating order. Nevertheless, while always improving on it, I found reasons to change its design...

— Pascal, Advertisement Necessary to those who have curiosity to see the Arithmetic Machine, and to operate it (1645)

When, several years ago, I saw for the first time an instrument which, when carried, automatically records the numbers of steps by a pedestrian, it occurred to me at once that the entire arithmetic could be subjected to a similar kind of machinery so that not only counting but also addition and subtraction, multiplication and division could be accomplished by a suitably arranged machine easily, promptly, and with sure results.

— Leibniz, on his calculating machine (1685)

The principle of the clock (input wheels and display wheels added to a clock like mechanism) for a direct-entry calculating machine couldn't be implemented to create a fully effective calculating machine without additional innovation with the technological capabilities of the 17th century. because their gears would jam when a carry had to be moved several places along the accumulator. The only 17th-century calculating clocks that have survived to this day do not have a machine-wide carry mechanism and therefore cannot be called fully effective mechanical calculators. A much more successful calculating clock was built by the Italian Giovanni Poleni in the 18th century and was a two-motion calculating clock (the numbers are inscribed first and then they are processed).

• In 1623, Wilhelm Schickard, a German professor of Hebrew and Astronomy, designed a calculating clock which he drew on two letters that he wrote to Johannes Kepler. The first machine to be built by a professional was destroyed during its construction and Schickard abandoned his project in 1624. These drawings had appeared in various publications over the centuries, starting in 1718 with a book of Kepler's letters by Michael Hansch, but in 1957 it was presented for the first time as a long-lost mechanical calculator by Dr. Franz Hammer. The building of the first replica in the 1960s showed that Schickard's machine had an unfinished design and therefore wheels and springs were added to make it work. The use of these replicas showed that the single-tooth wheel, when used within a calculating clock, was an inadequate carry mechanism. (see Pascal versus Schickard). This did not mean that such a machine could not be used in practice, but the operator when faced with the mechanism resisting rotation, in the unusual circumstances of a carry being required beyond (say) 3 dials, would need to "help" the subsequent carry to propagate.
• Around 1643, a French clockmaker from Rouen, after hearing of Pascal's work, built what he claimed to be a calculating clock of his own design. Pascal fired all his employees and stopped developing his calculator as soon as he heard of the news. It is only after being assured that his invention would be protected by a royal privilege that he restarted his activity. A careful examination of this calculating clock showed that it didn't work properly and Pascal called it an avorton (aborted fetus).
• In 1659, the Italian Tito Livio Burattini built a machine with nine independent wheels, each one of these wheels was paired with a smaller carry wheel. At the end of an operation the user had to either manually add each carry to the next digit or mentally add these numbers to create the final result.
• In 1666, Samuel Morland invented a machine designed to add sums of money, but it was not a true adding machine since the carry was added to a small carry wheel situated above each digit and not directly to the next digit. It was very similar to Burattini's machine. Morland created also a multiplying machines with interchangeable disks based on Napier's bones. Taken together these two machines provided a capacity similar to that of the invention of Schickard, although it is doubtful that Morland ever encountered Schickard's calculating clock.
• In 1673, the French clockmaker René Grillet described in Curiositez mathématiques de l'invention du Sr Grillet, horlogeur à Paris a calculating machine that would be more compact than Pascal's calculator and reversible for subtraction. The only two Grillet machines known have no carry mechanism, displaying three lines of nine independent dials they also have nine rotating napier's rod for multiplication and division. Contrary to Grillet's claim, it was not a mechanical calculator after all.

The 18th century

Overview

The 18th century saw the first mechanical calculator that could perform a multiplication automatically; designed and built by Giovanni Poleni in 1709 and made of wood, it was the first successful calculating clock. For all the machines built in this century, division still required the operator to decide when to stop a repeated subtraction at each index, and therefore these machines were only providing a help in dividing, like an abacus. Both pinwheel calculators and Leibniz wheel calculators were built with a few unsuccessful attempts at their commercialization.

Prototypes and limited runs

• In 1709, Italian Giovanni Poleni was the first to build a calculator that could multiply automatically. It used a pinwheel design, was the first operational calculating clock and was made of wood; he destroyed it after hearing that Antonius Braun had received 10,000 Guldens for dedicating a pinwheel machine of his own design to the Holy Roman Emperor Charles VI in Vienna.
• In 1725, the French Academy of Sciences certified a calculating machine derived from Pascal's calculator designed by Lépine, a French craftsman. The machine was a bridge in between Pascal's calculator and a calculating clock. The carry transmissions were performed simultaneously, like in a calculating clock, and therefore "the machine must have jammed beyond a few simultaneous carry transmissions".
• In 1727, German Anton Braun presented the first fully functional four-operation machine to Emperor Charles VI in Vienna. It was cylindrical in shape and was made of steel, silver and brass; it was finely decorated and looked like a renaissance table clock. His dedication to the emperor engraved on the top of the machine also reads "...to make easy to ignorant people, addition, subtraction, multiplication and even division".
• In 1730, the French Academy of Sciences certified three machines designed by Hillerin de Boistissandeau. The first one used a single-tooth carry mechanism which, according to Boistissandeau, wouldn't work properly if a carry had to be moved more than two places; the two other machines used springs that were gradually armed until they released their energy when a carry had to be moved forward. It was similar to Pascal's calculator but instead of using the energy of gravity Boistissandeau used the energy stored into the springs.
• In 1770, Philipp Matthäus Hahn, a German pastor, built two circular calculating machines based on Leibniz' cylinders. J. C. Schuster, Hahn's brother-in-law, built a few machines of Hahn's design into the early 19th century.
• In 1775, Lord Stanhope of the United Kingdom designed a pinwheel machine. It was set in a rectangular box with a handle on the side. He also designed a machine using Leibniz wheels in 1777. "In 1777 Stanhope produced the Logic Demonstrator, a machine designed to solve problems in formal logic. This device marked the beginning of a new approach to the solution of logical problems by mechanical methods."
• In 1784, German Johann-Helfrich Müller built a machine very similar to Hahn's machine.

The 19th century

Overview

Luigi Torchi invented the first direct multiplication machine in 1834. This was also the second key-driven machine in the world, following that of James White (1822).

The mechanical calculator industry started in 1851 Thomas de Colmar released his simplified Arithmomètre, which was the first machine that could be used daily in an office environment.

For 40 years, the arithmometer was the only mechanical calculator available for sale and was sold all over the world. By 1890, about 2,500 arithmometers had been sold plus a few hundreds more from two licensed arithmometer clone makers (Burkhardt, Germany, 1878 and Layton, UK, 1883). Felt and Tarrant, the only other competitor in true commercial production, had sold 100 comptometers in three years.

The 19th century also saw the designs of Charles Babbage calculating machines, first with his difference engine, started in 1822, which was the first automatic calculator since it continuously used the results of the previous operation for the next one, and second with his analytical engine, which was the first programmable calculator, using Jacquard's cards to read program and data, that he started in 1834, and which gave the blueprint of the mainframe computers built in the middle of the 20th century.

Desktop calculators produced

• In 1851, Thomas de Colmar simplified his arithmometer by removing the one-digit multiplier/divider. This made it a simple adding machine, but thanks to its moving carriage used as an indexed accumulator, it still allowed for easy multiplication and division under operator control. The arithmometer was now adapted to the manufacturing capabilities of the time; Thomas could therefore manufacture consistently a sturdy and reliable machine. Manuals were printed and each machine was given a serial number. Its commercialization launched the mechanical calculator industry. Banks, insurance companies, government offices started to use the arithmometer in their day-to-day operations, slowly bringing mechanical desktop calculators into the office.
• In 1878 Burkhardt, of Germany, was the first to manufacture a clone of Thomas' arithmometer. Until then Thomas de Colmar had been the only manufacturer of desktop mechanical calculators in the world and he had manufactured about 1,500 machines. Eventually twenty European companies will manufacture clones of Thomas' arithmometer until WWII.
• Dorr E. Felt, in the U.S., patented the Comptometer in 1886. It was the first successful key-driven adding and calculating machine. In 1887, he joined with Robert Tarrant to form the Felt & Tarrant Manufacturing Company. The comptometer-type calculator was the first machine to receive an all-electronic calculator engine in 1961 (the ANITA mark VII released by Sumlock comptometer of the UK).
• In 1890 W. T. Odhner got the rights to manufacture his calculator back from Königsberger & C, which had held them since it was first patented in 1878, but had not really produced anything. Odhner used his Saint Petersburg workshop to manufacture his calculator and he built and sold 500 machines in 1890. This manufacturing operation shut down definitively in 1918 with 23,000 machines produced. The Odhner Arithmometer was a redesigned version of the Arithmometer of Thomas de Colmar with a pinwheel engine, which made it cheaper to manufacture and gave it a smaller footprint while keeping the advantage of having the same user interface.
• In 1892 Odhner sold the Berlin branch of his factory, which he had opened a year earlier, to Grimme, Natalis & Co. They moved the factory to Braunschweig and sold their machines under the brand name of Brunsviga (Brunsviga is the Latin name of the town of Braunschweig). This was the first of many companies which would sell and manufacture clones of Odhner's machine all over the world; eventually millions were sold well into the 1970s.
• In 1892, William S. Burroughs began commercial manufacture of his printing adding calculator Burroughs Corporation became one of the leading companies in the accounting machine and computer businesses.
• The "Millionaire" calculator was introduced in 1893. It allowed direct multiplication by any digit – "one turn of the crank for each figure in the multiplier". It contained a mechanical product lookup table, providing units and tens digits by differing lengths of posts. Another direct multiplier was part of the Moon-Hopkins billing machine; that company was acquired by Burroughs in the early 20th century.

Automatic mechanical calculators

• In 1822, Charles Babbage presented a small cogwheel assembly that demonstrated the operation of his difference engine, a mechanical calculator which would be capable of holding and manipulating seven numbers of 31 decimal digits each. It was the first time that a calculating machine could work automatically using as input results from its previous operations. It was the first calculating machine to use a printer. The development of this machine, later called "Difference Engine No. 1," stopped around 1834.
• In 1847, Babbage began work on an improved difference engine design—his "Difference Engine No. 2." None of these designs were completely built by Babbage. In 1991 the London Science Museum followed Babbage's plans to build a working Difference Engine No. 2 using the technology and materials available in the 19th century.
• In 1855, Per Georg Scheutz completed a working difference engine based on Babbage's design. The machine was the size of a piano, and was demonstrated at the Exposition Universelle in Paris in 1855. It was used to create tables of logarithms.
• In 1875, Martin Wiberg re-designed the Babbage/Scheutz difference engine and built a version that was the size of a sewing machine.

Programmable mechanical calculators

• In 1834, Babbage started to design his analytical engine, which will become the undisputed ancestor of the modern mainframe computer with two separate input streams for data and program (a primitive Harvard architecture), printers for outputting results (three different kind), processing unit (mill), memory (store) and the first-ever set of programming instructions. In the proposal that Howard Aiken gave IBM in 1937 while requesting funding for the Harvard Mark I which became IBM's entry machine in the computer industry, we can read: "Few calculating machines have been designed strictly for application to scientific investigations, the notable exceptions being those of Charles Babbage and others who followed him. In 1812 Babbage conceived the idea of a calculating machine of a higher type than those previously constructed to be used for calculating and printing tables of mathematical functions. ....After abandoning the difference engine, Babbage devoted his energy to the design and construction of an analytical engine of far higher powers than the difference engine..."
• In 1843, during the translation of a French article on the analytical engine, Ada Lovelace wrote, in one of the many notes she included, an algorithm to compute the Bernoulli numbers. This is considered the first computer program.
• From 1872 until 1910, Henry Babbage worked intermittently on creating the mill, the "central processing unit" of his father's machine. After a few setbacks, he gave in 1906 a successful demonstration of the mill which printed the first 44 multiples of pi with 29 places of figures.

Cash registers

The cash register, invented by the American saloonkeeper James Ritty in 1879, addressed the old problems of disorganization and dishonesty in business transactions. It was a pure adding machine coupled with a printer, a bell and a two-sided display that showed the paying party and the store owner, if he wanted to, the amount of money exchanged for the current transaction.

The cash register was easy to use and, unlike genuine mechanical calculators, was needed and quickly adopted by a great number of businesses. "Eighty four companies sold cash registers between 1888 and 1895, only three survived for any length of time".

In 1890, 6 years after John Patterson started NCR Corporation, 20,000 machines had been sold by his company alone against a total of roughly 3,500 for all genuine calculators combined.

By 1900, NCR had built 200,000 cash registers and there were more companies manufacturing them, compared to the "Thomas/Payen" arithmometer company that had just sold around 3,300 and Burroughs had only sold 1,400 machines.

Prototypes and limited runs

• In 1820, Thomas de Colmar patented the Arithmometer. It was a true four operation machine with a one digit multiplier/divider (The Millionaire calculator released 70 years later had a similar user interface). He spent the next 30 years and 300,000 Francs developing his machine. This design was replaced in 1851 by the simplified arithmometer which was only an adding machine.
• From 1840, Didier Roth patented and built a few calculating machines, one of which was a direct descendant of Pascal's calculator.
• In 1842, Timoleon Maurel invented the Arithmaurel, based on the Arithmometer, which could multiply two numbers by simply entering their values into the machine.
• In 1845, Izrael Abraham Staffel first exhibited a machine that was able to add, subtract, divide, multiply and obtain a square root.
• Around 1854, Andre-Michel Guerry invented the Ordonnateur Statistique, a cylindrical device designed to aid in summarizing the relations among data on moral variables (crime, suicide, etc.)
• In 1872, Frank S. Baldwin in the U.S. invented a pinwheel calculator.
• In 1877 George B. Grant of Boston in the United States began producing the Grant mechanical calculating machine capable of addition, subtraction, multiplication and division. The machine measured 13x5x7 inches and contained eighty working pieces made of brass and tempered steel. It was first introduced to the public at the 1876 Centennial Exposition in Philadelphia.
• In 1883, Edmondson of the United Kingdom patented a circular stepped drum calculator.

1900s to 1970s

Mechanical calculators reach their zenith

Two different classes of mechanisms had become established by this time, reciprocating and rotary. The former type of mechanism was operated typically by a limited-travel hand crank; some internal detailed operations took place on the pull, and others on the release part of a complete cycle. The illustrated 1914 machine is this type; the crank is vertical, on its right side. Later on, some of these mechanisms were operated by electric motors and reduction gearing that operated a crank and connecting rod to convert rotary motion to reciprocating.

The latter type, rotary, had at least one main shaft that made one continuous revolution, one addition or subtraction per turn. Numerous designs, notably European calculators, had handcranks, and locks to ensure that the cranks were returned to exact positions once a turn was complete.

The first half of the 20th century saw the gradual development of the mechanical calculator mechanism.

The Dalton adding-listing machine introduced in 1902 was the first of its type to use only ten keys, and became the first of many different models of "10-key add-listers" manufactured by many companies.

In 1948 the cylindrical Curta calculator, which was compact enough to be held in one hand, was introduced after being developed by Curt Herzstark in 1938. This was an extreme development of the stepped-gear calculating mechanism. It subtracted by adding complements; between the teeth for addition were teeth for subtraction.

From the early 1900s through the 1960s, mechanical calculators dominated the desktop computing market. Major suppliers in the USA included Friden, Monroe, and SCM/Marchant. These devices were motor-driven, and had movable carriages where results of calculations were displayed by dials. Nearly all keyboards were full – each digit that could be entered had its own column of nine keys, 1..9, plus a column-clear key, permitting entry of several digits at once. (See the illustration below of a Marchant Figurematic.) One could call this parallel entry, by way of contrast with ten-key serial entry that was commonplace in mechanical adding machines, and is now universal in electronic calculators. (Nearly all Friden calculators, as well as some rotary (German) Diehls had a ten-key auxiliary keyboard for entering the multiplier when doing multiplication.) Full keyboards generally had ten columns, although some lower-cost machines had eight. Most machines made by the three companies mentioned did not print their results, although other companies, such as Olivetti, did make printing calculators.

In these machines, addition and subtraction were performed in a single operation, as on a conventional adding machine, but multiplication and division were accomplished by repeated mechanical additions and subtractions. Friden made a calculator that also provided square roots, basically by doing division, but with added mechanism that automatically incremented the number in the keyboard in a systematic fashion. The last of the mechanical calculators were likely to have short-cut multiplication, and some ten-key, serial-entry types had decimal-point keys. However, decimal-point keys required significant internal added complexity, and were offered only in the last designs to be made. Handheld mechanical calculators such as the 1948 Curta continued to be used until they were displaced by electronic calculators in the 1970s.

Typical European four-operation machines use the Odhner mechanism, or variations of it. This kind of machine included the Original Odhner, Brunsviga and several following imitators, starting from Triumphator, Thales, Walther, Facit up to Toshiba. Although most of these were operated by handcranks, there were motor-driven versions. Hamann calculators externally resembled pinwheel machines, but the setting lever positioned a cam that disengaged a drive pawl when the dial had moved far enough.

Although Dalton introduced in 1902 first 10-key printing adding (two operations, the other being subtraction) machine, these features were not present in computing (four operations) machines for many decades. Facit-T (1932) was the first 10-key computing machine sold in large numbers. Olivetti Divisumma-14 (1948) was the first computing machine with both printer and a 10-key keyboard.

Full-keyboard machines, including motor-driven ones, were also built until the 1960s. Among the major manufacturers were Mercedes-Euklid, Archimedes, and MADAS in Europe; in the USA, Friden, Marchant, and Monroe were the principal makers of rotary calculators with carriages. Reciprocating calculators (most of which were adding machines, many with integral printers) were made by Remington Rand and Burroughs, among others. All of these were key-set. Felt & Tarrant made Comptometers, as well as Victor, which were key-driven.

The basic mechanism of the Friden and Monroe was a modified Leibniz wheel (better known, perhaps informally, in the USA as a "stepped drum" or "stepped reckoner"). The Friden had an elementary reversing drive between the body of the machine and the accumulator dials, so its main shaft always rotated in the same direction. The Swiss MADAS was similar. The Monroe, however, reversed direction of its main shaft to subtract.

The earliest Marchants were pinwheel machines, but most of them were remarkably sophisticated rotary types. They ran at 1,300 addition cycles per minute if the bar is held down. Others were limited to 600 cycles per minute, because their accumulator dials started and stopped for every cycle; Marchant dials moved at a steady and proportional speed for continuing cycles. Most Marchants had a row of nine keys on the extreme right, as shown in the photo of the Figurematic. These simply made the machine add for the number of cycles corresponding to the number on the key, and then shifted the carriage one place. Even nine add cycles took only a short time.

In a Marchant, near the beginning of a cycle, the accumulator dials moved downward "into the dip", away from the openings in the cover. They engaged drive gears in the body of the machine, which rotated them at speeds proportional to the digit being fed to them, with added movement (reduced 10:1) from carries created by dials to their right. At the completion of the cycle, the dials would be misaligned like the pointers in a traditional watt-hour meter. However, as they came up out of the dip, a constant-lead disc cam realigned them by way of a (limited-travel) spur-gear differential. As well, carries for lower orders were added in by another, planetary differential. (The machine shown has 39 differentials in its accumulator!)

In any mechanical calculator, in effect, a gear, sector, or some similar device moves the accumulator by the number of gear teeth that corresponds to the digit being added or subtracted – three teeth changes the position by a count of three. The great majority of basic calculator mechanisms move the accumulator by starting, then moving at a constant speed, and stopping. In particular, stopping is critical, because to obtain fast operation, the accumulator needs to move quickly. Variants of Geneva drives typically block overshoot (which, of course, would create wrong results).

However, two different basic mechanisms, the Mercedes-Euklid and the Marchant, move the dials at speeds corresponding to the digit being added or subtracted; a moves the accumulator the slowest, and a , the fastest. In the Mercedes-Euklid, a long slotted lever, pivoted at one end, moves nine racks ("straight gears") endwise by distances proportional to their distance from the lever's pivot. Each rack has a drive pin that is moved by the slot. The rack for is closest to the pivot, of course. For each keyboard digit, a sliding selector gear, much like that in the Leibniz wheel, engages the rack that corresponds to the digit entered. Of course, the accumulator changes either on the forward or reverse stroke, but not both. This mechanism is notably simple and relatively easy to manufacture.

The Marchant, however, has, for every one of its ten columns of keys, a nine-ratio "preselector transmission" with its output spur gear at the top of the machine's body; that gear engages the accumulator gearing. When one tries to work out the numbers of teeth in such a transmission, a straightforward approach leads one to consider a mechanism like that in mechanical gasoline pump registers, used to indicate the total price. However, this mechanism is seriously bulky, and utterly impractical for a calculator; 90-tooth gears are likely to be found in the gas pump. Practical gears in the computing parts of a calculator cannot have 90 teeth. They would be either too big, or too delicate.

Given that nine ratios per column implies significant complexity, a Marchant contains a few hundred individual gears in all, many in its accumulator. Basically, the accumulator dial has to rotate 36 degrees (1/10 of a turn) for a , and 324 degrees (9/10 of a turn) for a , not allowing for incoming carries. At some point in the gearing, one tooth needs to pass for a , and nine teeth for a . There is no way to develop the needed movement from a driveshaft that rotates one revolution per cycle with few gears having practical (relatively small) numbers of teeth.

The Marchant, therefore, has three driveshafts to feed the little transmissions. For one cycle, they rotate 1/2, 1/4, and 1/12 of a revolution. . The 1/2-turn shaft carries (for each column) gears with 12, 14, 16, and 18 teeth, corresponding to digits 6, 7, 8, and 9. The 1/4-turn shaft carries (also, each column) gears with 12, 16, and 20 teeth, for 3, 4, and 5. Digits and are handled by 12 and 24-tooth gears on the 1/12-revolution shaft. Practical design places the 12th-rev. shaft more distant, so the 1/4-turn shaft carries freely-rotating 24 and 12-tooth idler gears. For subtraction, the driveshafts reversed direction.

In the early part of the cycle, one of five pendants moves off-center to engage the appropriate drive gear for the selected digit.

Some machines had as many as 20 columns in their full keyboards. The monster in this field was the Duodecillion made by Burroughs for exhibit purposes.

For sterling currency, £/s/d (and even farthings), there were variations of the basic mechanisms, in particular with different numbers of gear teeth and accumulator dial positions. To accommodate shillings and pence, extra columns were added for the tens digit, 10 and 20 for shillings, and 10 for pence. Of course, these functioned as radix-20 and radix-12 mechanisms.

A variant of the Marchant, called the Binary-Octal Marchant, was a radix-8 (octal) machine. It was sold to check very early vacuum-tube (valve) binary computers for accuracy. (Back then, the mechanical calculator was much more reliable than a tube/valve computer.)

As well, there was a twin Marchant, comprising two pinwheel Marchants with a common drive crank and reversing gearbox. Twin machines were relatively rare, and apparently were used for surveying calculations. At least one triple machine was made.

The Facit calculator, and one similar to it, are basically pinwheel machines, but the array of pinwheels moves sidewise, instead of the carriage. The pinwheels are biquinary; digits 1 through 4 cause the corresponding number of sliding pins to extend from the surface; digits 5 through 9 also extend a five-tooth sector as well as the same pins for 6 through 9.

The keys operate cams that operate a swinging lever to first unlock the pin-positioning cam that is part of the pinwheel mechanism; further movement of the lever (by an amount determined by the key's cam) rotates the pin-positioning cam to extend the necessary number of pins.

Stylus-operated adders with circular slots for the stylus, and side-by -side wheels, as made by Sterling Plastics (USA), had an ingenious anti-overshoot mechanism to ensure accurate carries.

The end of an era

Mechanical calculators continued to be sold, though in rapidly decreasing numbers, into the early 1970s, with many of the manufacturers closing down or being taken over. Comptometer type calculators were often retained for much longer to be used for adding and listing duties, especially in accounting, since a trained and skilled operator could enter all the digits of a number in one movement of the hands on a comptometer quicker than was possible serially with a 10-key electronic calculator. In fact, it was quicker to enter larger digits in two strokes using only the lower-numbered keys; for instance, a 9 would be entered as 4 followed by 5. Some key-driven calculators had keys for every column, but only 1 through 5; they were correspondingly compact. The spread of the computer rather than the simple electronic calculator put an end to the comptometer. Also, by the end of the 1970s, the slide rule had become obsolete.

See also

• Abacus
• Adding machine
• Calculator
• History of computing hardware
• Mechanical computer
• Tabulating machine
• George Brown (inventor)

Notes

1. An obsolete classification with possible discriminatory connotations, see Semitic_people#Antisemitism

References

1. Michael Williams, History of Computing Technology, IEEE Computer Society, p. 122 (1997)
2. Michael Williams, History of Computing Technology, IEEE Computer Society, p. 124, 128 (1997)
3. Prof. René Cassin, Pascal tercentenary celebration, London, (1942), Magazine Nature
4. ^ Jean Marguin (1994), p. 48
5. See Pascal's calculator#Competing designs
6. ^ Jean Marguin, p. 64-65 (1994)
7. Smith 1929, pp. 173–181
8. Beside two arithmometer clone makers from Germany and England, the only other company to offer calculators for sale was Felt & Tarrant from the USA which started selling their comptometer in 1887 but had only sold 100 machines by 1890.
9. Ernst Martin p. 133 (1925)
10. Ernst Martin p. 23 (1925)
11. #MARG,Jean Marguin p. 171, (1994)
12. Hyman, Anthony (1982). Charles Babbage: Pioneer of the Computer. Oxford University Press. ISBN 0-19-858170-X.
13. "The introduction of punched cards into the new engine was important not only as a more convenient form of control than the drums, or because programs could now be of unlimited extent, and could be stored and repeated without the danger of introducing errors in setting the machine by hand; it was important also because it served to crystallize Babbage's feeling that he had invented something really new, something much more than a sophisticated calculating machine." Bruce Collier, 1970
14. I. Bernard Cohen, p. 66-67, (2000)
15. Brian Randell, p. 187, 1975
16. Please see Pascaline#Pascal versus Schickard
17. "The arithmetical machine produces effects which approach nearer to thought than all the actions of animals. But it does nothing which would enable us to attribute will to it, as to the animals.", Pascal, Pensées Bartleby.com, Great Books online, Blaise Pasdcal, Thoughts
18. ^ Magazine Nature, (1942)
19. Scripta Mathematica, p. 128 (1932)
20. From the calculating machine of Pascal to the computer, p. 43 (1990)
21. (fr) La Machine d’arithmétique, Blaise Pascal, Wikisource
22. Guy Mourlevat, p. 12 (1988)
23. Courrier du CIBP, N°8, p. 9, (1986)
24. "...et si blocage il y avait, la machine était pratiquement inutilisable, ce qui ne fut jamais signalé dans les textes du XVIIIe siecle parmi ses défaults" Guy Mourlevat, p. 30 (1988)
25. Scripta Mathematica, p. 149 (1932)
26. Morar, Florin-Stefan (March 2015). "Reinventing machines: the transmission history of the Leibniz calculator". The British Journal for the History of Science. 48 (1): 123–146. doi:10.1017/S0007087414000429. ISSN 0007-0874. PMID 25833800. S2CID 38193192.
27. David Smith, p. 173-181 (1929)
28. As quoted in Smith 1929, pp. 180–181
29. See http://things-that-count.net
30. Translated from "j'en composai une troisième qui va par ressorts et qui est très simple en sa construction. C'est celle de laquelle, comme j'ai déjà dit, je me suis servi plusieurs fois, au vu et su d'une infinité de personnes, et qui est encore en état de servir autant que jamais. Toutefois, en la perfectionnant toujours, je trouvai des raisons de la changer" Avis nécessaire à ceux qui auront curiosité de voir la Machine d'Arithmétique et de s'en servir Wikisource: La Machine d’arithmétique, Blaise Pascal
31. Quoted in David Smith, p. 173, (1929)
32. Michael Williams, p. 124, 128 (1997) for Schikard's machine and the fact that the machines built by Burattini, Morland and Grillet were calculating clocks without a completely effective carry mechanism.
33. History of computer (retrieved on 1 February 2012)
34. Michael Williams, p. 122 (1997)
35. Michael Williams, p. 124, 128 (1997)
36. "The appearance of this small avorton disturbed me to the utmost and it dampened the enthusiasm with which I was developing my calculator so much that I immediately let go all of my employees..." translated from the French: "L'aspect de ce petit avorton me déplut au dernier point et refroidit tellement l'ardeur avec laquelle je faisais lors travailler à l'accomplissement de mon modèle qu'à l'instant même je donnai congé à tous les ouvriers..."
37. "But, later on, Lord Chancellor of France granted me a royal privilege which is not usual, and which will suffocate before their birth all these illegitimate avortons which, by the way, could only be born of the legitimate and necessary alliance of theory and art." translated from the French: "Mais, quelque temps après, Monseigneur le Chancelier par la grâce qu'il me fit de m'accorder un privilège qui n'est pas ordinaire, et qui étouffe avant leur naissance tous ces avortons illégitimes qui pourraient être engendrés d'ailleurs que de la légitime et nécessaire alliance de la théorie avec l'art"
38. "...a useless piece, perfectly clean, polished and well filed on the outside but so imperfect inside that it is of no use whatsoever." translated from the French: "...qu'une pièce inutile, propre véritablement, polie et très bien limée par le dehors, mais tellement imparfaite au dedans qu'elle n'est d'aucun usage"
39. All the quotes in this paragraph are found in (fr) Wikisource: Avis nécessaire à ceux qui auront curiosité de voir la Machine d'Arithmétique et de s'en servir.
40. Picture of Burattini's machine Archived 9 June 2010 at the Wayback Machine Florence, Istituto e Museo di Storia della Scienza, inv. 3179 (accessed on January, 09 2012)
41. ^ A calculator Chronicle, 300 years of counting and reckoning tools, p. 12, IBM
42. Michael Williams, p.140 (1997)
43. Picture of Morland multiplying machine Florence, Istituto e Museo di Storia della Scienza, inv. 679 (retrieved on January, 09 2012)
44. They belong to the Musée des Arts et Métiers in Paris.
45. "Grillet's machine doesn't even deserve the name of machine" translated from the French "La machine de Grillet ne mérite donc pas même le nom de machine", Jean Marguin, p.76 (1994)
46. Copy of Poleni's machine (it) Museo Nazionale della Scienza e della Tecnologia Leonardo Da Vinci. Retrieved 4 October 2010
47. Jean Marguin, p. 93-94 (1994)
48. translated from the French: "De plus le report ne s'effectuant pas en cascade, la machine devait se bloquer au-delà de quelques reports simultanés", Jean Marguin, p.78 (1994)
49. Jean Marguin, p.94-96 (1994)
50. #MARG, Jean Marguin, pages 80–81 (1994)
51. Marguin, p.83 (1994)
52. Picture of Hahn's Calculator IBM Collection of mechanical calculators
53. Jean Marguin, pages 84–86 (1994)
54. Door E. Felt, p.15-16 (1916)
55. "CNUM – 8KU54-2.5 : p.249 – im.253". cnum.cnam.fr.
56. "History of Computers and Computing, Mechanical calculators, 19th century, Luiggi Torchi". history-computer.com. 4 January 2021.
57. Roegel, Denis (2016). "Before Torchi and Schwilgué, There Was White". IEEE Annals of the History of Computing. 38 (4): 92–93. doi:10.1109/MAHC.2016.46. S2CID 28873771.
58. This is one third of the 120 years that this industry lasted
59. "www.arithmometre.org". arithmometre.org.
60. Felt, Dorr E. (1916). Mechanical arithmetic, or The history of the counting machine. Chicago: Washington Institute. p. 4.
61. ^ "The calculating engines of English mathematician Charles Babbage (1791–1871) are among the most celebrated icons in the prehistory of computing. Babbage's Difference Engine No.1 was the first successful automatic calculator and remains one of the finest examples of precision engineering of the time. Babbage is sometimes referred to as "father of computing." The International Charles Babbage Society (later the Charles Babbage Institute) took his name to honor his intellectual contributions and their relation to modern computers." Charles Babbage Institute (page. Retrieved 1 February 2012).
62. Ifrah G., The Universal History of Numbers, vol 3, page 127, The Harvill Press, 2000
63. Chase G.C.: History of Mechanical Computing Machinery, Vol. 2, Number 3, July 1980, IEEE Annals of the History of Computing, p. 204
64. Serial numbers and Years of manufacturing www.arithmometre.org, Valéry Monnier
65. J.A.V. Turck, Origin of modern calculating machines, The Western Society of Engineers, 1921, p. 75
66. ^ G. Trogemann, pages: 39–45
67. David J. Shaw: The Cathedral Libraries Catalogue, The British Library and the Bibliographical Society, 1998
68. J.A.V. Turck, Origin of modern calculating machines, The Western Society of Engineers, 1921, p. 143
69. Wolff, John (30 May 2007). "The "Millionaire" Calculating Machine - Technical Description". John Wolff's Web Museum. Retrieved 30 December 2019.
70. James Essinger, p.76 (2004)
71. "The better part of my live has now been spent on that machine, and no progress whatever having been made since 1834...", Charles Babbage, quoted in Irascible Genius, 1964, p.145
72. "It is reasonable to inquire, therefore, whether it is possible to devise a machine which will do for mathematical computation what the automatic lathe has done for engineering. The first suggestion that such a machine could be made came more than a hundred years ago from the mathematician Charles Babbage. Babbage's ideas have only been properly appreciated in the last ten years, but we now realize that he understood clearly all the fundamental principles which are embodied in modern digital computers" B. V. Bowden, 1953, pp. 6,7
73. Howard Aiken, 1937, reprinted in The origins of Digital computers, Selected Papers, Edited by Brian Randell, 1973
74. NCR Retrospective website. Retrieved October, 02 2012
75. History of the cash register. Retrieved October, 05 2012
76. See the number of machines built in 1890 in this paragraph
77. Dick and Joan's antique. Retrieved October, 02 2012
78. List of serial numbers by dates arithmometre.org. Retrieved 10 October 2012
79. Before the computer, James W. Cortada, p.34 ISBN 0-691-04807-X
80. A notable difference was that the Millionaire calculator used an internal mechanical product lookup table versus a repeated addition or subtraction until a counter was decreased down to zero and stopped the machine for the arithmometer
81. L'ami des Sciences 1856, p. 301 www.arithmometre.org (page. Retrieved 22 September 2010)
82. Larousse, P. (1886), Grand dictionnaire universel du XIX siècle, Paris, entry for A-M Guerry
83. Hook & Norman p.252 (2001): "Grant developed two models of his calculating machine: a Barrel model, which he exhibited at the Centennial Exposition along with his difference engine; and a Rack and Pinion model, of which he was able to sell 125 examples. Although Grant never made much money from his calculating machines, his experiences in designing and constructing them led him to establish the highly successful Grant Gear Works, which helped to pioneer the gear-cutting industry in the United States."
84. "Improved Calculating Machine", "Scientific American" Vol. XXXVI, No. 19, 12 May 1877 p.294 New York: Munn &Company (Publisher)
85. Patent application in French from www.ami19.org scanned by Valéry Monnier (retrieved on 12 January 2012)
86. "The Twin Marchant".
87. "John Wolff's Web Museum - Facit C1-13 - Technical Description".

Sources

• De la machine à calculer de Pascal à l'ordinateur (in French). Paris, France: Musée National des Techniques, CNAM. 1990. ISBN 2-908207-07-9.
• Trogemann, G.; Nitussov, A. (2001). Computing in Russia. Germany: GWV-Vieweg. ISBN 3-528-05757-2.
• Felt, Dorr E. (1916). Mechanical arithmetic, or The history of the counting machine. Chicago: Washington Institute.
• Marguin, Jean (1994). Histoire des instruments et machines à calculer, trois siècles de mécanique pensante 1642–1942 (in French). Hermann. ISBN 978-2-7056-6166-3.
• Mourlevat, Guy (1988). Les machines arithmétiques de Blaise Pascal (in French). Clermont-Ferrand: La Française d'Edition et d'Imprimerie.
• Taton, René (1969). Histoire du calcul. Que sais-je ? n° 198 (in French). Presses universitaires de France.
• Turck, J.A.V. (1921). Origin of Modern Calculating Machines. The Western Society of Engineers. Reprinted by Arno Press, 1972 ISBN 0-405-04730-4.
• Ginsburg, Jekuthiel (2003). Scripta Mathematica (Septembre 1932-Juin 1933). Kessinger Publishing, LLC. ISBN 978-0-7661-3835-3.
• Martin, Ernst (1992) . The Charles Babbage Institute (ed.). The Calculating Machines (Die Rechenmaschinen). Cambridge, Massachusetts: The MIT Press.
• Cohen, I. Bernard (2000). Howard Aiken : Portrait of a Computer Pioneer. Cambridge, Massachusetts: The MIT Press. ISBN 9-780262-531795.
• Smith, David Eugene (1929). A Source Book in Mathematics. New York and London: McGraw-Hill Book Company, Inc.
• Moseley, Maboth (1964). Irascible Genius, Charles Babbage Inventor. London: Hutchinson & Co, Ltd.
• Bowden, B. V. (1953). Faster than thought. New York, Toronto, London: Pitman publishing corporation.
• Williams, Michael R. (1997). History of Computing Technology. Los Alamitos, California: IEEE Computer Society. ISBN 0-8186-7739-2.
• Randell, Brian (1973). The origins of Digital computers, Selected Papers. Springer-Verlag. ISBN 3-540-06169-X.
• IBM. A calculator Chronicle, 300 years of counting and reckoning tools. New York.
• Collier, Bruce (1990). The little engine that could've: The calculating machines of Charles Babbage. Garland Publishing Inc. ISBN 0-8240-0043-9.
• Essinger, James (2004). Jacquard's Web. Oxford University Press. ISBN 0-19-280577-0.
• Hook, Diana H.; Norman, Jeremy M. (2001). Origins of Cyberspace. Novato, California: historyofscience.com. ISBN 0-930405-85-4.
• M.E.P (31 October 1942). "Pascal tercentenary celebration". Nature. 150 (3809). London: 527. Bibcode:1942Natur.150..527M. doi:10.1038/150527a0.
• Prof. S. Chapman (31 October 1942). "Blaise Pascal (1623-1662) Tercentenary of the calculating machine". Nature. 150 (3809). London: 508–509. Bibcode:1942Natur.150..508C. doi:10.1038/150508a0.
• "Usage de la machine". Courrier du Centre International Blaise Pascal (in French) (8). Clermont-Ferrand: 4–25. 1986.

External links

• Wolff, John (2014). "Calculating Machines". John Wolff's Web Museum.
• Mařík, Robert Mechanical Calculators playlist on YouTube
• List of Mechanical Calculators
• Calculating with Mechanical Calculators
• International Forum Historical Office e.V.: www.ifhb.de International club on research of historical calculating and office machines.
• Media related to Mechanical calculators at Wikimedia Commons

• Mechanical calculators
• Office equipment
• Mathematical tools