Backflow prevention device - Misplaced Pages

(Redirected from Cross connection control & backflow prevention) Device that prevents undesired water flow

This article needs additional citations for verification. Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed.
Find sources: "Backflow prevention device" – news · newspapers · books · scholar · JSTOR (March 2013) (Learn how and when to remove this message)

A backflow prevention device is used to protect potable water supplies from contamination or pollution due to backflow.

In water distribution systems, water is normally maintained at a significant pressure to enable water to flow from the tap, shower, or other fixture. Water pressure may fail or be reduced when a water main bursts, pipes freeze, or there is unexpectedly high demand on the water system (for example, when several fire hydrants are opened). Reduced pressure in the pipe may allow contaminated water from the soil, from storage, or from other sources to be drawn up into the system.

Terminology

Backflow means the undesirable reversal of flow of a liquid, gas, or suspended solid into the potable water supply; a backflow preventer is designed to keep this from happening. Points at which a potable water system connects with a non-potable water system are called cross connections. Such connections occur naturally in appliances such as clothes washers and dishwashers, but they must be carefully designed and installed to prevent backflow. Another common location for a backflow preventer is the connection of a fire sprinkler system to a water main, to prevent pressurized water from flowing from the fire suppression system into the public water supply.

Back-siphonage occurs when higher pressure fluids, gases, or suspended solids move to an area of lower pressure fluids. For example, when a drinking straw is used to consume a beverage, suction reduces the pressure of fluid inside the straw, causing liquid to move from the cup to inside the straw and then into the drinker's mouth. A significant drop of pressure in a water delivery system creates a similar suction, pulling possibly undesirable material into the system. This is an example of an indirect cross-connection.

Back-pressure occurs for example when air is blown through the straw and bubbles begin to erupt at the submerged end. If, instead of air, natural gas had been forced into a potable water tank, the gas in turn could be carried to a kitchen faucet. This is an example of a direct cross-connection, with undesirable material being pushed into the system.

Back pressure can force an undesirable contaminant to enter potable water piping. Sources of back pressure may be boilers, heat exchanging equipment, power washing equipment, fire sprinklers, or pumps in the water distribution system. In some cases there may be an almost continuous risk of overcoming the static water pressure in the piping. To reduce the risk of contamination, a backflow preventer can be fitted. A backflow preventer is also important when potentially toxic chemicals are used, for instance for commercial/industrial descaling of boilers, or when chemical bleaches are used for residential power washing.

A closely related device is the backwater valve, which is designed to prevent sewage from backing up into a building and causing basement flooding.

Preventive devices

The simplest, most reliable way to provide backflow prevention is to provide an air gap. An air gap is simply an open vertical space between any device that connects to a plumbing system (like a valve or faucet) and any place where contaminated water can collect or pool. A simple air gap has no moving parts, other than flowing water. Many plumbing codes specify a minimum air gap distance required for various circumstances, such as a drain connection for a dishwasher, e.g., BS 6282.

Alternatively, a specialized backflow preventer valve may be installed at strategic locations in the plumbing system wherever there is a risk of contaminated fluids entering the water supply pipes. These valves are used where there is not sufficient vertical clearance or physical space to install an air gap, or when pressurized operation or other factors rule out use of an air gap. Because these valves use moving parts, they are often required to be inspected or tested periodically.

Regulatory requirements

To prevent contamination due to back pressure, many health regulatory regimes require an air gap or mechanical backflow prevention assembly between the delivery point of mains water and local storage or use. Where submerged mains inflow is permitted, a backflow prevention assembly is required, which protects the potable water system from contamination hazards. A check valve is a basic form of backflow prevention, but often more complex devices are required because check valves are not considered to be reliable, when compared to more sophisticated devices with redundancies and reduced-pressure zones.

In many countries. approved backflow prevention assemblies are required by law, and must be installed in accordance with plumbing or building codes. A typical backflow assembly has test cocks and shut-off valves, and must be tested when installed, if relocated or repaired, and also on a periodic basis.

In the US, the Environmental Protection Agency (EPA) holds local water suppliers responsible for maintaining a certain amount of purity in potable water systems. Many states and/or local municipalities require annual testing of backflow prevention assemblies. In most cases, the law requires a double check (DC), reduced pressure principle device (RP) device, or an air gap when backflow prevention is mandated.

Partial list of backflow prevention devices and assemblies

Air gap (AG the purest form of backflow prevention)
Atmospheric vacuum breaker (AVB)
Check valve (usually not a legally approved method of backflow prevention.)
Chemigation valve (primarily used in agriculture)
Double check valve assembly (DCVA)
Dual check valve (A dual check is not a testable device and is mainly used on residential customers)
Pressure vacuum breaker assembly (PVB)
Reduced pressure zone device (RPZ)
Spill resistant pressure vacuum breaker assembly (SPVB)
Vacuum breaker

References

"Backwater Valve Installation". Absolute Draining & Plumbing. Retrieved 9 October 2014.
"The Water Supply (Water Fittings) Regulations 1999". Archived from the original on 23 August 2010. Retrieved July 26, 2010.

External links

v t e Backflow and prevention
Backflow prevention methods	Atmospheric vacuum breaker Air gap Check valve Chemigation valve Double check valve Hydrostatic loop Pressure vacuum breaker Reduced pressure zone device Vacuum breaker

v t e Plumbing
Fundamental concepts	Air gap (plumbing) Backflow Compatibility (chemical) Corrosion Drain (plumbing) Drinking water Fuel gas Friction loss Grade (slope) Greywater Heat trap Hydrostatic loop Leak Neutral axis Onsite sewage facility Pressure Sanitary sewer Sewer gas Sewage Sewerage Siphon Storm sewer Stormwater Surface tension Tap water Thermal expansion Thermal insulation Thermosiphon Trap (plumbing) Venturi effect Wastewater Water hammer Water supply network Water table Well
Technology	Brazing British Standard Pipe (BSP) Cast iron pipe Chemical drain cleaners Compression fitting Copper tubing Crimp (joining) Drain-waste-vent system Ductile iron pipe Flare fitting Garden Hose Thread (GHT) Gasket Hydronics Leak detection National Pipe Thread (NPT) Nominal Pipe Size (NPS) O-ring Oakum Pipe (fluid conveyance) Pipe dope Pipe support Plastic pipework Push-to-pull compression fittings Putty Sealant Sewage pumping Soldering Solvent welding Swaging Thread seal tape Threaded pipe Tube bending Water heat recycling
Components	Atmospheric vacuum breaker Automatic bleeding valve Automatic faucet Backflow prevention device Ball valve Bleed screw Booster pump Butterfly valve Check valve Chemigation valve Chopper pump Circulator pump Cistern Closet flange Concentric reducer Condensate pump Coupling (piping) Diaphragm valve Dielectric union Double check valve Eccentric reducer Expansion tank Faucet aerator Float switch Float valve Floor drain Flow limiter Flushing trough Flushometer Gate valve Globe valve Grease trap Grinder pump Hose coupling Manifold Needle valve Nipple (plumbing) Pinch valve Piping and plumbing fitting Plug (sanitation) Pressure regulator Pressure vacuum breaker Pressure-balanced valve Pump Radiator (heating) Reduced pressure zone device Reducer Relief valve Riser clamp Rooftop water tower Safety valve Sewage pump Street elbow Submersible pump Tap (valve) Thermostatic mixing valve Trench drain Vacuum breaker Vacuum ejector Valve Water tank Zone valve
Plumbing fixtures	Accessible bathtub Bathtub Bidet Dehumidifier Dishwasher Drinking fountain Electric water boiler Evaporative cooler Flush toilet Garbage disposal unit Hot water storage tank Humidifier Icemaker Instant hot water dispenser Laundry tub Shower water recycling shower Sink Storage water heater Sump pump Tankless water heater Urinal Washing machine Washlet Water dispenser Water filter Water heater Water softener
Specialized tools	Basin wrench Blowtorch Borescope Core drill Drain cleaner Driving cap Flare-nut wrench Pipecutter Pipe wrench Plumber's snake Plumber wrench Plunger Strap wrench Tap and die
Measurement and control	Control valve Flow sensor Pressure sensor Water detector Water metering
Professions, trades, and services	Hydronic balancing Hydrostatic testing Leak detection Mechanical, electrical, and plumbing Pipe marking Pipefitter Pipelayer Plumber
Industry organizations and standards	International Association of Plumbing and Mechanical Officials (IAPMO) NSF International Plumbing & Drainage Institute (PDI) Uniform Plumbing Code (UPC) World Plumbing Council (WPC)
Health and safety	Plumbing code Scalding Waterborne disease
See also	Fire sprinkler system Piping Template:HVAC Template:Public health Template:Sewerage Template:Toilets Template:Wastewater

Categories: