Double junction - Misplaced Pages

(Redirected from Diamond junction) Railway junction

This article has multiple issues. Please help improve it or discuss these issues on the talk page. (Learn how and when to remove these messages)

This article relies largely or entirely on a single source. Relevant discussion may be found on the talk page. Please help improve this article by introducing citations to additional sources.
Find sources: "Double junction" – news · newspapers · books · scholar · JSTOR (February 2017)

The examples and perspective in this article may not represent a worldwide view of the subject. You may improve this article, discuss the issue on the talk page, or create a new article, as appropriate. (February 2021) (Learn how and when to remove this message)

(Learn how and when to remove this message)

Double junction, or level junction (left hand running)

A double junction is a railway junction where a double-track railway splits into two double track lines. Usually, one line is the main line and carries traffic through the junction at normal speed, while the other track is a branch line that carries traffic through the junction at reduced speed.

A number of configurations are possible.

At grade

Diamond

The simplest and oldest arrangement consists of two turnouts (points) and a fixed Diamond crossing. Because the diamond needs to be relatively coarse, say 1 in 8, the curve radius is necessarily small, leading to a speed of perhaps 25 km/h (16 mph). This type of junction is common on street-running tramways, where speeds are quite low and junction must fit into the available road space. Because the points are close together, the entire junction can be controlled by the mechanical point rodding of a single signal box.

Signal passed at danger (SPAD) protection — A train from R to P with 12 points reverse is protected from a train from P doing a SPAD by 11 points also lying reverse. A train from P to Q is NOT protected from a train from R doing a SPAD.

Switched diamond

The fixed diamond can be replaced with a switched diamond, which eliminates the gap in rails at the K-crossing, which allows a higher speed if the geometry is poor. However, switched diamonds are not a perfect solution to the K-crossing problem, as the switches are very coarse compared to the finer switches of a turnout, and require high maintenance. The additional ends are also awkward to control unless power operated point machines are used.

Ladder

An improved junction replaces the diamond with turnouts, which can be of as fine an angle as possible, so that this junction can carry branch traffic at high speed. This configuration assumes power operation of the points, as high speed turnouts are generally not suitable for mechanical operation. The high speed turnouts may require more than one point machine each. The turnouts can have no superelevation while the curve in the branch can; therefore the radius in the turnouts must be greater than the radius of the curve in the branch.

Since the ladder type junction requires much more length, diamond type junctions can only be converted into ladder types if there is room and no bridges, tunnels, or platforms in the way.

SPAD protection

Essentially the same as for a double junction with diamond.

Examples include Harris Park railway station, Sydney.

Single lead left hand

A single lead junction is used where traffic density is lower, and moves one of the turnouts on the main line onto the branch. This reduces the number of turnouts on the main line that are subject to wear.

Space permitting, a single lead junction may be a stage towards construction of a higher speed ladder junction. This is shown as blue dashed line on the diagram.

Risk

However, unlike in the ladder, branch trains in opposite directions can collide head-on at 32 if either one passes a signal at danger (SPAD). This has contributed to fatal accidents, e.g. in the UK at: Glasgow Bellgrove on 6 March 1989 and Newton on 21 July 1991. These risks can be reduced by trap points, ATP or TPWS.

Wear and tear

The diamond crossing is a high wearing and undesirable component:

gaps in the K-crossings, and V-crossing.
vibration at gaps caused by wheels jumping over these gaps.
small parts which allow the joins to bend.
insulated block joints, if needed for track circuits, create more joints to bend.
inconvenience when trying to tamp the track.
inconvenience of speed limits to reduce vibration.
difficulty of obtaining "track possession" to allow maintenance to be carried out.
often the existing tracks do not have space to allow the alternative to be built as an afterthought.
when starting on a "green field" site, the opportunity to install two high-speed turnouts to replace each diamond should not be missed.
the insulated block joint problem can be reduced if axle counters can replace the track circuits over the crossings.
switched diamonds are only suitable for limited range of crossing angles, and they have their own problems.
- say 1:5 (too coarse) to 1:10 (too coarse).
the tracks through diamonds needed to be co-planar, and if not poor geometry and poor speeds may result.
the legs of the diamond should be straight if possible.
Trains (magazine) devoted an issue to diamonds, which, in their opinion, are NOT a railroad's best friend
- where traffic over a diamond crossing is heavier in one direction than the other, special measures can be taken to improve performance in the heavier traffic direction. See Trains.

Single lead right hand

A right hand single lead junction cannot protect against a collision should the Q-P train overrun the signal protecting the junction, and this is not ameliorated by reverting to a double junction.

Diamond and wide centres

A double junction with a diamond can have its speed limit raised if the track centres are widened from say 4 m to say 12 m to allow for a fixed coarse-angled diamond crossing (say 1 in 8.25) with fine-angled turnouts (1 in 15).

If the legs of the coarse crossing X are straight and flat, then this arrangement eliminates the need for switched diamonds and their inconvenient moving parts.

SPAD protection

Essentially the same as for a double junction with diamond.

Scissors crossovers

Fast speed

The Channel Tunnel has at its entrances a scissors crossover implemented with two turnouts replacing the usual diamond crossing in the middle. This is only possible because of the wide track centres caused by the wide spacing of the entrances to the tunnel. The result is high speeds on the turnout routes through those turnouts and minimum wear and tear.

All the turnouts, P, Q, R, S, X1 and X2 are all the same high speed. Track centres need to be at least twice the normal track centres as if there was a hidden track in between.

All the turnouts are identical except for handedness.

Medium speed

Were this junction be made with a Diamond crossing in the middle, speeds through the turnout would be much reduced, and wear and tear on the diamond would be high.

Very slow speed

At Hornsby the site is very constrained and speeds through the diamond crossing was only 8km/h, increased to 15km/h after a few changes. The site does not permit any further increase, and the restrictions dating from 1890 remain. Track centres are 12' (3.66m) throughout.

Colour coding is as follows:

Black - unchanged
Red - scissors crossovers
Blue - roads and road overbridges
Purple - other rail tracks.

Speed limits

on the straight through the scissors crossovers are 40km/h.
on the curves through the diamond crossing "X" are now 15km/h.
on the curves from S - P2 and P1 to P are 40km/h.

Grade separated

Main article: Flying junction

Flyovers

A double junction can be grade separated so that there is no flat crossing, reducing conflicts and reducing congestion. Flyovers require a lot of space both lengthwise and crosswise, and cannot always be built. Flying junction example at Aynho Junction. Diving junctions such as at Chatswood are a variant. Weaver Junction is the oldest flying junction in the United Kingdom and perhaps the world. See also Aynho Junction.

SPAD protection

Because the diamond crossing or equivalent is eliminated, one of the potential SPAD hazards is also eliminated, leaving just the merging junction hazard.

References

Hall, Chapter 6: Hidden Dangers - Single Lead Junctions

Hall, Stanley (1999). Hidden Dangers: Railway Safety in the Era of Privatisation. Sheperton: Ian Allan. ISBN 0-7110-2679-3.

v t e Railway track layouts
Railway track	Single track Passing loop Double track Quadruple track Crossover
Rail sidings	Balloon loop Headshunt Pocket track Refuge siding Rail yard Classification yard
Junctions	Flying junction Level junction Double junction Facing and trailing Grand union Grand circle / roundabout Wye Switch / turnout / points Swingnose crossing Level crossing
Stations	Railway platform Bay Island Side Split Terminal station Balloon loop Spanish solution Cross-platform interchange Interchange station Infill station
Hillclimbing	Horseshoe curve Zig Zag / Switchback Spiral
Track geometry	Track gauge Ruling gradient Minimum curve radius Cant Cant deficiency

v t e Rail infrastructure
Tracks (history)	Axe ties Ballast Baulk road Breather switch Cant Clip and scotch Date nail Fastening system Fishplate Ladder track Minimum radius Profile Tie/Sleeper Transition curve
Trackwork	Balloon loop Classification yard Headshunt Pocket track Junction Gauntlet track Guide bar Passing loop Track gauge dual gauge Rail track tramway track Rail yard Railway electrification overhead lines third rail ground-level power supply Railway turntable Transfer table (traverser) Roll way Siding refuge siding Switch Track geometry Water crane Water trough Wye
Signalling and safety	Anti-trespass panels Block post Buffer stop Catch points Defect detector Derailer Guard rail Interlocking Level crossing Loading gauge Platform screen doors Railway signal Signalling control Structure gauge Signal bridge Tell-tale Train stop Wayside horn
Structures	Coaling tower Motive power depot/Railway workshop Platform Roundhouse Shed for trains for goods Station building clock ghost list Water stop
Types	Industrial Military Private station list

Category:

Rail junction types