Misplaced Pages

Potassium dichromate

Article snapshot taken from Wikipedia with creative commons attribution-sharealike license. Give it a read and then ask your questions in the chat. We can research this topic together.
(Redirected from Kali bichromicum) Not to be confused with Potassium chromate.
Potassium dichromate
Potassium dichromate
Unit cell of potassium dichromate
Names
IUPAC name Potassium dichromate(VI)
Other names
  • potassium bichromate
  • bichromate of potash
  • dipotassium dichromate
  • dichromic acid, dipotassium salt
  • chromic acid, dipotassium salt
  • lópezite
Identifiers
CAS Number
3D model (JSmol)
ChEMBL
ChemSpider
ECHA InfoCard 100.029.005 Edit this at Wikidata
EC Number
  • 231-906-6
PubChem CID
RTECS number
  • HX7680000
UNII
UN number 3288
CompTox Dashboard (EPA)
InChI
  • InChI=1S/2Cr.2K.7O/q;;2*+1;;;;;;2*-1Key: KMUONIBRACKNSN-UHFFFAOYSA-N
SMILES
  • ..(=O)(=O)O()(=O)=O
Properties
Chemical formula K2Cr2O7
Molar mass 294.185 g/mol
Appearance red-orange crystalline solid
Odor odorless
Density 2.676 g/cm, solid
Melting point 398 °C (748 °F; 671 K)
Boiling point 500 °C (932 °F; 773 K) decomposes
Solubility in water 4.9 g/100 mL (0 °C)
13 g/100 mL (20 °C)
102 g/100 mL (100 °C)
Solubility insoluble in alcohol, acetone.
Refractive index (nD) 1.738
Structure
Crystal structure Triclinic (α-form, <241.6 °C)
Coordination geometry Tetrahedral (for Cr)
Thermochemistry
Heat capacity (C) 219 J/mol
Std molar
entropy
(S298)
291.2 J/(K·mol)
Std enthalpy of
formation
fH298)
−2033 kJ/mol
Hazards
Occupational safety and health (OHS/OSH):
Main hazards carcinogenic, corrosive
GHS labelling:
Pictograms GHS03: OxidizingGHS05: CorrosiveGHS06: ToxicGHS08: Health hazardGHS09: Environmental hazard
NFPA 704 (fire diamond)
NFPA 704 four-colored diamondHealth 4: Very short exposure could cause death or major residual injury. E.g. VX gasFlammability 0: Will not burn. E.g. waterInstability 1: Normally stable, but can become unstable at elevated temperatures and pressures. E.g. calciumSpecial hazard OX: Oxidizer. E.g. potassium perchlorate
4 0 1OX
Flash point Non-flammable
Lethal dose or concentration (LD, LC):
LD50 (median dose) 25 mg/kg (oral, rat)
Safety data sheet (SDS) ICSC 1371
Related compounds
Other anions Potassium chromate
Potassium molybdate
Potassium tungstate
Other cations Ammonium dichromate
Sodium dichromate
Related compounds Potassium permanganate
Except where otherwise noted, data are given for materials in their standard state (at 25 °C , 100 kPa). checkverify (what is  ?) Infobox references
Chemical compound

Potassium dichromate, K2Cr2O7, is a common inorganic chemical reagent, most commonly used as an oxidizing agent in various laboratory and industrial applications. As with all hexavalent chromium compounds, it is acutely and chronically harmful to health. It is a crystalline ionic solid with a very bright, red-orange color. The salt is popular in laboratories because it is not deliquescent, in contrast to the more industrially relevant salt sodium dichromate.

Chemistry

Production

Potassium dichromate is usually prepared by the reaction of potassium chloride on sodium dichromate. Alternatively, it can be also obtained from potassium chromate by roasting chromite ore with potassium hydroxide. It is soluble in water and in the dissolution process it ionizes:

K2Cr2O7 → 2 K + Cr
2O
7 Cr
2O
7 + H2O ⇌ 2 CrO
4 + 2 H

Reaction

Potassium dichromate is an oxidising agent in organic chemistry, and is milder than potassium permanganate. It is used to oxidize alcohols. It converts primary alcohols into aldehydes and, under more forcing conditions, into carboxylic acids. In contrast, potassium permanganate tends to give carboxylic acids as the sole products. Secondary alcohols are converted into ketones. For example, menthone may be prepared by oxidation of menthol with acidified dichromate. Tertiary alcohols cannot be oxidized.

In an aqueous solution the color change exhibited can be used to test for distinguishing aldehydes from ketones. Aldehydes reduce dichromate from the +6 to the +3 oxidation state, changing color from orange to green. This color change arises because the aldehyde can be oxidized to the corresponding carboxylic acid. A ketone will show no such change because it cannot be oxidized further, and so the solution will remain orange.

When heated strongly, it decomposes with the evolution of oxygen.

4 K2Cr2O7 → 4 K2CrO4 + 2 Cr2O3 + 3 O2

When an alkali is added to an orange-red solution containing dichromate ions, a yellow solution is obtained due to the formation of chromate ions (CrO2−4). For example, potassium chromate is produced industrially using potash:

K2Cr2O7 + K2CO3 → 2 K2CrO4 + CO2

The reaction is reversible.

Treatment with cold sulfuric acid gives red crystals of chromic anhydride (chromium trioxide, CrO3):

K2Cr2O7 + 2 H2SO4 → 2 CrO3 + 2 KHSO4 + H2O

On heating with concentrated acid, oxygen is evolved:

2 K2Cr2O7 + 8 H2SO4 → 2 K2SO4 + 2 Cr2(SO4)3 + 8 H2O + 3 O2

Uses

Potassium dichromate has few major applications, as the sodium salt is dominant industrially. The main use is as a precursor to potassium chrome alum, used in leather tanning.

Cleaning

Like other chromium(VI) compounds (chromium trioxide, sodium dichromate), potassium dichromate has been used to prepare "chromic acid" for cleaning glassware and etching materials. Because of safety concerns associated with hexavalent chromium, this practice has been largely discontinued.

Construction

It is used as an ingredient in cement in which it retards the setting of the mixture and improves its density and texture. This usage commonly causes contact dermatitis in construction workers.

Photography and printing

In 1839, Mungo Ponton discovered that paper treated with a solution of potassium dichromate was visibly tanned by exposure to sunlight, the discoloration remaining after the potassium dichromate had been rinsed out. In 1852, Henry Fox Talbot discovered that exposure to ultraviolet light in the presence of potassium dichromate hardened organic colloids such as gelatin and gum arabic, making them less soluble.

These discoveries soon led to the carbon print, gum bichromate, and other photographic printing processes based on differential hardening. Typically, after exposure, the unhardened portion was rinsed away with warm water, leaving a thin relief that either contained a pigment included during manufacture or was subsequently stained with a dye. Some processes depended on the hardening only, in combination with the differential absorption of certain dyes by the hardened or unhardened areas. Because some of these processes allowed the use of highly stable dyes and pigments, such as carbon black, prints with an extremely high degree of archival permanence and resistance to fading from prolonged exposure to light could be produced.

Dichromated colloids were also used as photoresists in various industrial applications, most widely in the creation of metal printing plates for use in photomechanical printing processes.

Chromium intensification or Photochromos uses potassium dichromate together with equal parts of concentrated hydrochloric acid diluted down to approximately 10% v/v to treat weak and thin negatives of black and white photograph roll. This solution reconverts the elemental silver particles in the film to silver chloride. After thorough washing and exposure to actinic light, the film can be redeveloped to its end-point yielding a stronger negative which is able to produce a more satisfactory print.

A potassium dichromate solution in sulfuric acid can be used to produce a reversal negative (that is, a positive transparency from a negative film). This is effected by developing a black and white film but allowing the development to proceed more or less to the end point. The development is then stopped by copious washing and the film then treated in the acid dichromate solution. This converts the silver metal to silver sulfate, a compound that is insensitive to light. After thorough washing and exposure to actinic light, the film is developed again allowing the previously unexposed silver halide to be reduced to silver metal. The results obtained can be unpredictable, but sometimes excellent results are obtained producing images that would otherwise be unobtainable. This process can be coupled with solarisation so that the end product resembles a negative and is suitable for printing in the normal way.

Cr(VI) compounds have the property of tanning animal proteins when exposed to strong light. This quality is used in photographic screen-printing.

In screen-printing a fine screen of bolting silk or similar material is stretched taut onto a frame similar to the way canvas is prepared before painting. A colloid sensitized with a dichromate is applied evenly to the taut screen. Once the dichromate mixture is dry, a full-size photographic positive is attached securely onto the surface of the screen, and the whole assembly exposed to strong light – times vary from 3 minutes to a half an hour in bright sunlight – hardening the exposed colloid. When the positive is removed, the unexposed mixture on the screen can be washed off with warm water, leaving the hardened mixture intact, acting as a precise mask of the desired pattern, which can then be printed with the usual screen-printing process.

Analytical reagent

Because it is non-hygroscopic, potassium dichromate is a common reagent in classical "wet tests" in analytical chemistry.

Ethanol determination

Acidified solution of potassium dichromate

The concentration of ethanol in a sample can be determined by back titration with acidified potassium dichromate. Reacting the sample with an excess of potassium dichromate, all ethanol is oxidized to acetic acid:

CH3CH2OH + 2 → CH3COOH + H2O

Full reaction of converting ethanol to acetic acid:

3 C2H5OH + 2 K2Cr2O7 + 8 H2SO4 → 3 CH3COOH + 2 Cr2(SO4)3 + 2 K2SO4 + 11 H2O

The excess dichromate is determined by titration against sodium thiosulfate. Adding the amount of excess dichromate from the initial amount, gives the amount of ethanol present. Accuracy can be improved by calibrating the dichromate solution against a blank.

One major application for this reaction is in old police breathalyzer tests. When alcohol vapor makes contact with the orange dichromate-coated crystals, the color changes from Cr(VI) orange to Cr(III) green. The degree of the color change is directly related to the level of alcohol in the suspect's breath.

Silver test

When dissolved in an approximately 35% nitric acid solution it is called Schwerter's solution and is used to test for the presence of various metals, notably for determination of silver purity. Pure silver will turn the solution bright red, sterling silver will turn it dark red, low grade coin silver (0.800 fine) will turn brown (largely due to the presence of copper which turns the solution brown) and even green for 0.500 silver. Brass turns dark brown, copper turns brown, lead and tin both turn yellow while gold and palladium do not change.

Sulfur dioxide test

Potassium dichromate paper can be used to test for sulfur dioxide, as it turns distinctively from orange to green. This is typical of all redox reactions where hexavalent chromium is reduced to trivalent chromium. Therefore, it is not a conclusive test for sulfur dioxide. The final product formed is Cr2(SO4)3.

SO2 + K2Cr2O7 + 3H2SO4 → K2SO4 + Cr2(SO4)3 + 3 H2O

Wood treatment

Potassium dichromate is used to stain certain types of wood by darkening the tannins in the wood. It produces deep, rich browns that cannot be achieved with modern color dyes. It is a particularly effective treatment on mahogany.

Natural occurrence

A ~10 mm crystal of potassium dichromate in the same form as the mineral lópezite

Potassium dichromate occurs naturally as the rare mineral lópezite. It has only been reported as vug fillings in the nitrate deposits of the Atacama Desert of Chile and in the Bushveld igneous complex of South Africa.

Safety

Patch test

In 2005–06, potassium dichromate was the 11th-most-prevalent allergen in patch tests (4.8%).

Potassium dichromate is one of the most common causes of chromium dermatitis; chromium is highly likely to induce sensitization leading to dermatitis, especially of the hand and forearms, which is chronic and difficult to treat. Toxicological studies have further illustrated its highly toxic nature. With rabbits and rodents, concentrations as low as 14 mg/kg have shown a 50% fatality rate amongst test groups. Aquatic organisms are especially vulnerable if exposed, and hence responsible disposal according to the local environmental regulations is advised.

As with other Cr(VI) compounds, potassium dichromate is carcinogenic. The compound is also corrosive and exposure may produce severe eye damage or blindness. Human exposure further encompasses impaired fertility.

References

  1. "POTASSIUM DICHROMATE LISTING" (PDF). US EPA. 2015-07-23.
  2. Binnewies, M.; Milke, E. (2002). Thermochemical Data of Elements and Compounds (2 ed.). Weinheim: Wiley-VCH. p. 405. ISBN 978-3-527-30524-7.
  3. Sigma-Aldrich Co., Chromium(VI) oxide. Retrieved on 2014-06-15.
  4. Like all compounds of hexavalent chromium, potassium dichromate is carcinogenic
  5. Chambers, Michael. "ChemIDplus - 7778-50-9 - KMUONIBRACKNSN-UHFFFAOYSA-N - Potassium dichromate - Similar structures search, synonyms, formulas, resource links, and other chemical information".
  6. ^ Gerd Anger, Jost Halstenberg, Klaus Hochgeschwender, Christoph Scherhag, Ulrich Korallus, Herbert Knopf, Peter Schmidt, Manfred Ohlinger, "Chromium Compounds" in Ullmann's Encyclopedia of Industrial Chemistry, Wiley-VCH, Weinheim, 2005. doi:10.1002/14356007.a07_067
  7. L. T. Sandborn. "l-Menthone". Organic Syntheses; Collected Volumes, vol. 1, p. 340.
  8. M. Saha; C. R. Srinivas; S. D. Shenoy; C. Balachandran (May 1993). "Footwear dermatitis". Contact Dermatitis. 28 (5): 260–264. doi:10.1111/j.1600-0536.1993.tb03428.x. PMID 8365123. S2CID 23159708.
  9. Pekka Roto; Hannele Sainio; Timo Reunala; Pekka Laippala (January 1996). "Addition of ferrous sulfate to cement and risk of chromium dermatitis among construction workers". Contact Dermatitis. 34 (1): 43–50. doi:10.1111/j.1600-0536.1996.tb02111.x. PMID 8789225. S2CID 27027304.
  10. Jewitt, Jeff (1997). Hand-Applied Finishes. Newtown, Connecticut: Taunton Press. ISBN 978-1-56158-154-2.
  11. "Lópezite: Lópezite mineral information and data".
  12. Zug KA, Warshaw EM, Fowler JF Jr, Maibach HI, Belsito DL, Pratt MD, Sasseville D, Storrs FJ, Taylor JS, Mathias CG, Deleo VA, Rietschel RL, Marks J. Patch-test results of the North American Contact Dermatitis Group 2005–2006. Dermatitis. 2009 May–Jun;20(3):149-60.
  13. Farokh J. Master (2003). Diseases of Skin. New Delhi: B Jain Pub Pvt Ltd. p. 223. ISBN 978-81-7021-136-5.
  14. "Potassium dichromate MSDS". Sigma-Aldrich. Retrieved 2011-07-20.
  15. IARC (2012) . Volume 100C: Arsenic, Metals, Fibres, and Dusts (PDF). Lyon: International Agency for Research on Cancer. ISBN 978-92-832-0135-9. Retrieved 2020-01-05. There is sufficient evidence in humans for the carcinogenicity of chromium (VI) compounds. Chromium (VI) compounds cause cancer of the lung. Also positive associations have been observed between exposure to Chromium (VI) compounds and cancer of the nose and nasal sinuses. There is sufficient evidence in experimental animals for the carcinogenicity of chromium (VI) compounds. Chromium (VI) compounds are carcinogenic to humans (Group 1).
  16. "Potassium dichromate MSDS". JT Baker.

External links

Potassium compounds
H, (pseudo)halogens
chalcogens
pnictogens
B, C group
transition metals
organic
Chromates and dichromates
Chromates
Chlorochromates
Chromate esters
Dichromates
Related
Categories: